Featured Products

Highest quality standards are achieved through the implementations of latest technology, decades of experience and everlasting moral values , which have helped us to retain our customers as well as multiply them.

Welcome to TEJA METALLURGICALS AND CHEMICALS

Drawing Lubricant

  /> </div>
<div class=

Product description

Tejalube 2000 is a drawing lubricant with very high film strength and is used on cold extrusion and cold operation. It is applied by dip process on the metallic surface which has been properly bonderized. It reacts with Tejalube 2000 coating, forming a lubricant layer, which helps in cold forming of metal and retards the formation of rust.

Product Specifications

Colour Light Pale Yellow Powder
Chemical Composition Blend of soap powders, additives surfaces etc.
Odour Nil
Foaming Tendency Very Moderate
Reliability Good
Handling Avoid Skin Contact
Solubility Infinite
pH Alkaline Range
Toxicity Nil
Flash Point Nil
Pollution Hazard Moderate

Product Operating Data

Concentration 3 - 5%
Dip Time 2 – 3 minutes
Temperature 60 - 80°c
Pointage: TAFa -1 ml (min)

Product Operating Procedure

Concentration of Tejalube 2000 solution may range from 3 -15% depending upon the end operation. Extrusion operation generally requires more concentration than tube-drawing, wire drawing or deep drawing but the optimum concentration is best determined experimentally.

Before using the lubricant determine the free acidity according to method given below. If this is outside th range adjust it by adding required amount of caustic soda or sulphuric acid.

The treatment consists of dipping the job which have been bonderized and properly rinsed in Tejalube 2000 at 60-80° C 4 – 5 mts to permit the lubricant to penetrate and react with coating. The temperature at which Tejalube 2000 is operating should not be allowed to vary more than ±20°C. The temperature is established for each project and generally is in the range of 60 – 70°c. It drainage is a problem because of the shape of components the upper range is advisable.

Product Application Equipment

Tejalube 2000 tank should be fabricated with 3 to 4 mm thick M.S. Plates with continuous current heating system.

Testing and Control Procedure

Sample taken from the hot lubricatly bath may be analyzed immediately. If it is allowed to cool it will become thick and must be repeated for analysis.

Free Acidity

Take 100 ml of Tejalube 2000 from bath. Transfer 10 ml to conical flask. Add 200 ml of (ISOPROPANOL with 2 – 3 drop of phenolphthalein ). Heat to boiling when still hot titrate against N/10 sodium Hydroxide to a permanent pink colour N/10 NaoH used will give free acidity. It should be 0 – 1.00 mls.

Chemical Replenishment

If free acidity is more than 1.00. Add 200 gms of caustic soda (Dissolved in water) in 1000 litres of solution. This will lower the F.A. By 0.5 m.

Safety Measures

Tejalube 2000 is a highly alkaline material. Direct contact can cause burns to eyes and skin, therefore use adequate ventilation. Avoid breathing vapour or mist, do not take internally.

In case of contact, immediately wash eyes or skin with plenty of water for at lease 15 minutes. Get medical attention remove contaminated clothing and shoes, wash them before re-use. If swallowed, wash out mouth with water. Give several gears of water to drink followed by milk of magnesia. Incas of severe exposure get medical attention.

General Information

Corrosion Resistance: Excellent
Lubrication: Excellent.

Our Vision

* To embrace new technologies and methods. * To give unsurpassed products and services to the clients. * To constantly look for improvement and changes.

Site Designed & Maintained by Aman Infotech
Accelerator For Phosphating Chemical, Blackening Salt, Carnallite Fluxes, Chromatising Chemicals, Combined Degreasing Derusting And Zinc Phosphating, Cover Fluxes, Degreasing Chemicals, Derusting And Descaling Chemical, Dip Iron Phosphating Chemicals, Drawing Lubricant, Fluxes For Aluminium Alloys, Forging Chemicals, Furnace Cleaning Flux, Heavy Zinc Phosphating Chemical, Hexachloroethane, Manganese Phosphating Chemical, Paint Stripping Chemicals, Passivation Chemicals, Pretreatment Chemicals, Products, Rust Preventive Oil, Spray Dip Iron Phosphating Chemical, Tricoat Phosphating Chemical, Wire And Tube Drawing Chemicals, Zinc Calcium Phosphating Chemical, Zinc Phosphating Chemical